XBee 1mW Wire Antenna
This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Related products
Arduino Leonardo, ATmega32U4, USB
Specifications
- Microcontroller: ATmega32u4
- Operating Voltage: 5V
- Input Voltage: 7-12V (recommended)
- Digital I/O Pins: 20
- PWM Channels: 7
- Analog Input Channels: 12
- DC Current per I/O Pin: 40 mA
- Flash Memory: 32 KB (ATmega32u4) of which 4 KB is used for the bootloader
- SRAM: 2.5 KB (ATmega32u4)
- EEPROM: 1 KB (ATmega32u4)
- Clock Speed: 16 MHz
Arduino MEGA 2560 R3 (ATMEGA2560-16AU MCU)
Overview
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
Arduino Nano V3.0 CH340 Improved Atmega328P USB to TTL with USB cable
Overview:
- Microcontroller: Atmega328
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins: 6
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory:32 KB (ATmega328) of which 0.5 KB used by bootloader
- SRAM:2 KB (ATmega328)
- EEPROM:1 KB (ATmega328)
- Clock Speed:16 MHz
GLT240128-WB (LCD Graphic RS 232 BLU/WHT)
Raspberry Pi Compute Module 3 – 4Gbytes eMMC Flash
Raspberry Pi Calculation Module 3
Raspberry Compute Module 3 is for designers who prefer Raspberry Pi3 functionality but require a smaller form factor (67.6 mm X 31 mm) for their embedded design. These modules are DDR2-SODIMM, mechanically compatible system-on-a-chip (SoM) that includes a BCM2837 processor system-on-a-chip (SoC) with 1 GB of LPDDR2 RAM and 4 GB of eMMC flash. In addition, these modules have an additional input/output (I/O) interface in addition to the Raspberry Pi Model A/B board.
U-BLOX NEO-6M module (GY-GPS6MV2)
- 1 — u-blox NEO-6M GY-GPS6MV2 GPS module with on board EEPROM
- 1 — GPS antenna
- 1 — 1x4 male header
WiFly RN-171
- Ultra low power for battery powered applications
- Firmware configurable transmit power: 0dBm to +12dBm
- Hardware interfaces: UART
- Supports Adhoc and infrastructure networking modes
- User programmable GPIO & ADCs
- Real-time clock for time-stamping, auto-sleep, and auto-wakeup modes
- Run directly from batteries or regulated power supplies
- Configuration over serial or wireless interface using simple ASCII commands
- Over the air firmware upgrade
- Secure Wi-Fi authentication schemes (WEP/WPA/WPA2)
- Full onboard TCP/IP stack (no external drivers required)
Reviews
There are no reviews yet.