UNO R3 WiFI Development Board ATmega328P+ESP8266 (32Mb RAM) |USB-TTL CH340G Development Board
Original price was: ₨2,500.00.₨1,800.00Current price is: ₨1,800.00.
Introduction
Arduino UNO R3 WiFi is a board that combines the versatility of an Arduino UNO and the connectivity of an ESP8266, the platform includes 32Mbit of flash memory shared between the two microprocessors and a convenient selector for switching the serial lines.
Description:
Arduino UNO R3 WiFi (ESP8266) with 32Mb flash memory.
Features
Microcontroller: Atmel ATmega328
- Operating voltage: 5V
- Input Voltage: (suggested) 7-12V
- Input Voltage: (maximum) 6-20V
- Digital I/O: 14 (6 of them can output PWM signals)
- Analog Input: 6
- 10-bit ADC
- I/O maximum current: 40 mA
- Flash Memory: 32KB (0.5KB used by bootloader)
- SRAM: 2KB
- EEPROM: 1KB
- SPI
- I²C
- Clock Frequency: 16MHz
Microcontroller: ESP8266
- Processore: 80 Mhz 32 bit microcontroller
- 64 KB instruction RAM, 96 KB data RAM
- Wi-Fi standard IEEE 802.11 b/g/n
- Security: WEP, WPA/WPA2
- 16 pin GPIO
- SPI
- I²C
- UART
- 10-bit ADC
Specifications:
- Weight: 21.2 g
- Width: 69 mm
- Length: 32 mm
- Height: 13 mm
- Compatible with Arduino Shields
Table DIP- switch:
| Connection | DIP | ||||||
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | |
| ATmega328<->ESP8266 | ON | ON | OFF | OFF | OFF | OFF | OFF |
| USB <->ATmega328 | OFF | OFF | ON | ON | OFF | OFF | OFF |
| USB<->ESP8266 (Update firmware or sketch) | OFF | OFF | OFF | OFF | ON | ON | ON |
| USB<->ESP8266 (communication) | OFF | OFF | OFF | OFF | ON | ON | OFF |
| All independent | OFF | OFF | OFF | OFF | OFF | OFF | OFF |
You must be logged in to post a review.
Related products
Arduino MEGA 2560 R3 (ATMEGA2560-16AU MCU)
Overview
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 (datasheet). It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
Leonardo R3 Development Board ATMEGA32U4
Product specifications:
• Controller: ATmega32u4 • Work record: 16 MHz • Working voltage: 5V • Input voltage (recommended): 7-12V • Digital IO port: 20 • PWM channel: 7 • Analog input: 12 • 5V digital / analog port maximum allowable current: 40 mA • 3.3V digital / analog port maximum allowable current: 50 mA • Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader • SRAM: 2.5 KB (ATmega32u4) • EEPROM: 1 KB (ATmega32u4)
Raspberry Pi Compute Module 3 – 4Gbytes eMMC Flash
Raspberry Pi Calculation Module 3
Raspberry Compute Module 3 is for designers who prefer Raspberry Pi3 functionality but require a smaller form factor (67.6 mm X 31 mm) for their embedded design. These modules are DDR2-SODIMM, mechanically compatible system-on-a-chip (SoM) that includes a BCM2837 processor system-on-a-chip (SoC) with 1 GB of LPDDR2 RAM and 4 GB of eMMC flash. In addition, these modules have an additional input/output (I/O) interface in addition to the Raspberry Pi Model A/B board.
WiFly RN-171
- Ultra low power for battery powered applications
- Firmware configurable transmit power: 0dBm to +12dBm
- Hardware interfaces: UART
- Supports Adhoc and infrastructure networking modes
- User programmable GPIO & ADCs
- Real-time clock for time-stamping, auto-sleep, and auto-wakeup modes
- Run directly from batteries or regulated power supplies
- Configuration over serial or wireless interface using simple ASCII commands
- Over the air firmware upgrade
- Secure Wi-Fi authentication schemes (WEP/WPA/WPA2)
- Full onboard TCP/IP stack (no external drivers required)
Reviews
There are no reviews yet.