-21%
MQ-2 (Smoke sensor-HBO, LPG, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide)
Original price was: ₨320.00.₨300.00Current price is: ₨300.00.
MQ-5 (Gas Sensor module LPG, Natural Gas, Coal Gas)
Original price was: ₨400.00.₨370.00Current price is: ₨370.00.
MQ-4 (Methane Gas Sensor module for Arduino)
Original price was: ₨280.00.₨220.00Current price is: ₨220.00.
Gas sensor MQ4 registers presence and concentration of natural gas and methane (CH4). The best results are given when gas is in liquid form, however, since situations like this are rare, it does its job pretty well when in gas form, too. It needs a bit of time to warm up in order to work correctly.
Description
Description:
The MQ-4-sensitive material used in pure air conductivity is the lower tin dioxide (sno2). When the sensor is present in a medium in which a combustible gas, the conductivity of the sensor increases with the concentration of combustible gases in the air. The use of a simple circuit can be converted into a change in the conductivity of the gas concentration with an appropriate output signal. MQ-4 methane gas sensor for high sensitivity, propane, butane and has good sensitivity. The sensor can detect various flammable gases, especially natural gas, is a low-cost sensor for a wide variety of applications.
For household or factory methane gases, natural gas and other control devices for testing natural gas, methane 300-10000mln-1;
Module Features:
1, using a high-quality two-panel design, with a power indicator and information on the output of the TTL signal;
2, with the possibility of switching the signal of the switch (TTL) and the analogue signal of the AO;
3, TTL The output signal is low. (When the low light output is output, a microcontroller or relay module can be directly connected)
4, analog output voltage, the higher the concentration, the higher the voltage.
5, methane, natural gas has a higher sensitivity to detection.
6, there are four screw holes for easy positioning;
7, Product dimensions: 32 (l) * 20 (w) * 22 (H)
8, with a long service life and reliable stability
9. characteristics of rapid response and recovery
Electrical properties:
Input voltage: dc5V power (current): 150mA
Output: TTL Digital 0 and 1 (0.1 and 5 V)
AO output: 0.1-0. 3 V (relatively clean), the highest concentration of voltage is about 4 V
Special note: the sensor works, it is necessary to warm up about 20 s, the measured data become stable, the fever sensor is normal, because the internal heating wire, if it’s hot is not normal.
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
MQ-6 LPG Gas Sensor Module
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 300 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
TMP006 (Contact-less Infrared Temperature Measurement)
The TMP006 works with 3v to 5v, so it can be used with most microcontrollers without the need for a level shifter. It connects via the i2c bus and is addressable so you can have up to 8 TMP006 sensors on the same bus.
Features:
- 20mm x 20mm (board w/o headers)
- Uses I2C 7-bit addresses between 0x40 and 0x47, selectable with jumpers
- Interface Type : I2C Arduino driver module
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
Reviews
There are no reviews yet.