-14%
MICS-6814 (Air Quality Co, NH3, Nitrogen Oxide Gas Sensor)
Original price was: ₨6,500.00.₨6,150.00Current price is: ₨6,150.00.
MiCS-5524 (CO, Alcohol and VOC Gas Sensor)
Original price was: ₨2,850.00.₨2,450.00Current price is: ₨2,450.00.
Features:
- MiCS5524 CO, Alcohol and VOC Gas Sensor
- Robust MEMS (Micro Electro Mechanical System) Sensor
- Operating Voltage: 4.9V to 5.1V
- Analog Output via Ao pin (voltage increases as amount of any of the detected gases increases)
- For hobby use
- Current Draw: 25 to 35mA
- Works with Arduino, Teensy & Photon boards. Can be used with Raspberry Pi if you can use an Analog to Digital Converter
Description
Suitable Uses:
- Carbon Monoxide Detection
- Natural Gas Leak Detection
- Monitoring Air Quality
- Early Fire Detection
- Breathalyzer (alcohol detection)
- Only 4 Pins: 5V: Power, GND: Ground
- Ao: Analog Output (0V to 5V: as the amount of detected gases increases, voltage increases)
- En: Output Enable (to turn off the sensor for power consumption, send a HIGH 5V signal)
Detection ranges:
- Carbon Monoxide CO: approx 1 to 1000 ppm
- Ammonia: approx 1 to 500 ppm
- Ethanol: approx 10 to 500 ppm
- H2: approx 1 – 1000 ppm
- Methane: approx 1000++ ppm
- Propane: approx 1000++ ppm
- Iso-Butane: approx 1000++ ppm
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
AMG8834
Temperature Sensor Digital, Infrared (IR) 14-SMD Module
Product Specifications
| Sensor type | Infrared array sensor | |
| Maximum output current | 10mA | |
| Sensing distance | 7m | |
| Switch mode | digital | |
| Installation type | Surface mount | |
| Number of pins | 14 | |
| Maximum supply current | 4.5 mA | |
| size | 11.6 x 8 x 4.3mm | |
| height | 4.3mm | |
| length | 11.6mm | |
| series | Grid-EYE | |
| Maximum working temperature | +80 °C | |
| Maximum operating supply voltage | 5 V DC | |
| Minimum operating temperature | -20 °C | |
| width | 8mm |
DHT11 (Temperature and Humidity Sensor Module)
DHT11 Temperature and Humidity Sensor Module with LED Power Supply Indicators
Features:
- Can detect surrounding environment of the humidity and temperature
- DHT11 sensor adopts
- Humidity measurement range: 20%-95%, humidity measurement error: +-5%
- Temperature measurement range: 0 -50 ;measurement error: +-2 degrees
- Working voltage 3.3 V-5 V
- Output form: digital output
- Has fixed bolt hole and easy installation
- PCB size: 3.1cm x 1.4cm
DHT22- (Temperature and humidity sensor)
Product description:
The DHT22 module is designed to measure the temperature and humidity of the atmosphere. The difference from the younger model (DHT11), The DHT22 has a wide range and a high precision determination of temperature and humidity. The sensor works on the OneWire bus, which makes it possible to connect it to the Arduino only three wires ( two of which are POwer supply). Low power consumption allows you to install it on stand-alone devices.
MQ-5 (Gas Sensor module LPG, Natural Gas, Coal Gas)
Overview
- Sensitive for LPG, natural gas, coal gas
- An increase in the output voltage along with the concentration of the measured gases
- Rapid reaction and recovery
- Adjustable sensitivity
- Output indicator
Gas Sensor type |
Sensitive gas |
Application |
| MQ-135 Gas Sensor | Benzene, alcohol, smoke | Air Quality Monitoring |
| MQ-2 gas sensor | HBO, propane, hydrogen | Gas leak detector |
| MQ-3 gas sensor | Alcohol, ethanol | Carbon alcohol, Breathalyzer |
| MQ-5 Gas Sensor | CIS, natural gas, coal gas | Gas leak detector |
| MQ-7 gas sensor | Carbon monoxide | Carbon Monoxide Monitor |
Sharp IR Long Range Sensor – 20 cm to 150 cm
- Infrared range finder 20cm(~8") to 150cm (~60")
- Analog interface
T000220 (Arduino TinkerKit Touch Sensor Module)
This TinkerKit sensor is a touch sensitive device that provides an output when it detects skin contact. The sensor is connected to an Arduino board via a TinkerKit Shield to form part of the TinkerKit modular prototyping system.
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
Reviews
There are no reviews yet.