GY-652 (Air Pressure + Magnetic Field Sensor Module)
This is the GY-652 Sensor Module with HMC5983 and BMP180 Electronic Compass which enables us to measure Atmospheric Pressure and Magnetic Fields about 3 axes along with Pressure.
– Model: GY-652
– The use of chip: HMC5983 + BMP180
– Power supply :3-5v (internal low dropout regulator)
– Communication modes: standard IIC communication protocol)
– Magnetic field range: ± 0.88 to ± 8.1 gauss
– Pressure Range :300-1100hPa
– Chip 12bit AD converter, 16-bit data output
– Machine welding process to ensure quality
– Size: 13mm * 14mm (standard pitch 2.54mm)
– for ARDUINO test code
Related products
BMP280 (I2C/SPI Digital Barometric Pressure Sensor Module for Arduino)
The BMP280 sensor is an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI.
Features:
- Pressure range: 300 ~ 1100hPa (altitude 9000 m ~ -500 m); - Working voltage: 1.71 - 3.6VDC; - Low power consumption: 4μA; - High precision: at low-power mode, the resolution is 0.06hPa (0.5 meters); - Temperature output; - Communication interface: I2C or SPI; typical application: - GPS precise navigation (dead reckoning, the upper and lower bridge detection, etc.); - indoor and outdoor navigation; - The weather forecast; - The vertical velocity indication (rise / sink speed); Note: You need to add 5V to 3.3V level converter circuit between Arduino UNO R3 and the module.
GO2Y0A21YK
GO2Y0A21YK
Infrared distance measuring sensor (including dedicated data line)Technical Parameters:
- Model : GP2Y0A21YK (GP2D12 upgrade)
- Voltage: 4.5-5. 5V
- Current: 33-40mA
- Port: Analog
- Detection distance: 10-80cm
- Data line: 3P 20cm
- Wire: 24# American standard line
- Interface: 3P DuPont SVG compatible Arduino sensor expansion board
HTG3515CH- (Voltage Output Temperature and Humidity Sensor)
Voltage Output Temperature and Humidity Sensor HTG3515CH
Relative Humidity and Temperature Module
SPECIFICATIONS:
- Suitable for small bulk assembly
- Product free from Lead, Cr (6+), Cd and Hg. Compliant with RoHS
- Full interchangeability. Better than +/-3%RH and +/-0.25°C
- Humidity calibrated within +/- 3% RH @ 55% RH
- Temperature measurement through NTC direct output
Based on the rugged HUMIREL humidity sensor, HTG3515CH is a dedicated humidity and temperature plug and play transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made possible with the module’s humidity linear voltage and direct NTC outputs. HTG3515CH is designed for high volume and demanding applications. 
T000220 (Arduino TinkerKit Touch Sensor Module)
This TinkerKit sensor is a touch sensitive device that provides an output when it detects skin contact. The sensor is connected to an Arduino board via a TinkerKit Shield to form part of the TinkerKit modular prototyping system.
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TCS34725 (RGB Color Sensor with IR filter and White LED)
OVERVIEW:
1. Red, Green, Blue (RGB), and White Light Sensing with IR Blocking Filter
2. Programmable Analog Gain and Integration Time
3. 3,800,000:1 Dynamic Range
4. Very High Sensitivity: Ideally Suited for Operation Behind Dark Glass
5. Maskable Interrupt
6. Programmable Upper and Lower Thresholds with Persistence Filter
7. Power Management
8. Low Power: 2.5-uA Sleep State
9. 65-uA Wait State with Programmable Wait State Time from 2.4 ms to > 7 Seconds
10. I2C Fast Mode Compatible Interface
11. Data Rates up to 400 kbit/s
12. Input Voltage Levels Compatible with VDD or 1.8 V Bus
13. Register Set and Pin Compatible with the TCS3x71 Series
14. Small 2 mm*2.4 mm Dual Flat No-Lead (FN)
TTP 223B (Touch Thumb Sensor Module)
Product description:
This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensitivity well decrease as isolation get thick.
Reviews
There are no reviews yet.