GPS Shield with Data Logger (SD Card) for Arduino UNO +
A GPS module breakout board designed for Global Positioning System receiver with SD interface. It is easy to use for logging the GPS data into SD card. 5V/3.3V compatible operation voltage level make it compatible with Arduino UNO, Mega 2560 or Leonardo boards, leaf maple, IFlat32 and other arduino compatible boards. It is a compact, high performance, with low power consumption GPS engine board. It uses ublox’s NEO-6M GPS SiRF Star III chipset which can track up to 20 satellites at a time and perform fast TTFF in weak signal environments.
Description
Applications:
It’s suitable for the following applications with Arduino or Arduino compatible boards.
- Automotive navigation
- Personal positioning
- Fleet management
- Marine navigation
Features & Specifications:
- uBlox Neo 6M GPS module
- Micro SD interface for data logging
- 5 Hz update rate
- External GPS antenna
- Power and GPS fix indicator LEDs
- Reset Button
- Baud rate : 9600
- Update rate: 1Hz (Default), 5Hz (Max)
- Active antenna design with high receive sensitivity, compatible normal antenna
- Extremely fast time to first fix at low signal level
- UART interface
- Operation temperature: -40 ~ +85
- Shield Functions : Storage, Wireless
- Board Size : 56mm x 54mm
- Operation Leve : Digital 3.3V/5v
- Stackable : Yes
- Size: 53.0mm x 60mm
- GPS antenna Cable length: 3 meters approx
- Weight : 25.00g
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
Arduino Shield RAMPS-FD for Arduino Due 3D printer controller
When you use Arduino Due as the controller of your 3D Printer, you may find the RAMPS1.4 is not compatible with DUE.As you know the Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3, the importance is the Atmel SAM3X8E chip used on the Due operates at 3.3V,worse applying 5V to the Due's inputs will likely damage the chip.
So we create a new RAMPS variant which is compatible with the Due to replace Ramps 1.4.
CC3000 WiFi Shield for Arduino
CC3000 is a fully-equipped wireless network processor, which simplifies the execution of Internet connectivity . SIMPLELINK WIFI can greatly reduce the host microcontroller (MCU) software requirements , making use of any low-cost and low- power MCU embedded applications can be the ideal solution
Wireless Network Processor : IEEE802.11b / g
Embedded IPV4TCP/IP stack
The radio industry\’s best performance:
Tx Power : 11MBPSj for +18 DBM, CCK
RX Sensitivity :-86DBM, 8% packet error rate (PER), 11MBPS
Memory package with a compact , low processing millions of instructions every second (MIPS), low-cost microcontroller to work together :
2K Bytes Flash
250 bytes of RAM
Operating temperature range : -20 to 70 degrees
MICO Shield for Arduino
MICO Shield make it easy for Arduino users to create projects using cell phones. MICO can answer and place calls, present caller with voice prompt and accept touch tone commands.
MICO connects to a cell phone via audio jack and it has circuits to detect and answer calls. It then uses pre-recorded voice prompts to present information and options to callers, and touch-tone telephone keypad entry to gather responses. Responses can then be used to control lights, motors and other actuators, and get readings of temperature, wind speed, proximity and other sensors. The caller can be just a few feet or hundreds of miles away!
MICO is an acronym for Mobile Interactive voice response & COntrol. The word Mico in Portuguese means small monkey. It’s pronounced “mee co”.
Micro SD TF Memory Card Shield Module SPI For Arduino
Features:
Supports Micro SD cards, Micro SDHC card(Micro SD<=2G, Mirco SDHC<=32G).
Level conversion circuit board that interfaces level for 5V or 3.3V.
Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board.
It is a standard SPI communication interface.
4 M2 screw positioning holes for easy installation.
Motor Drive Shield (L293D) for Arduino
L293D is a monolithic integrated, high voltage, high current, 4-channel driver
- Can drive 4 DC motors or 2 stepper motors or 2 Servo.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 10V DC.
Simcom- SIM900
With a tiny configuration of 24mm x 24mm x 3mm, SIM900 can meet almost all the space requirements in your applications, such as M2M, smart phone, PDA and other mobile devices.
The keypad and SPI display interface will give you the flexibility to develop customized applications.
Serial port and Debug port can help you easily develop your applications.
One audio channel includes a microphone input and a speaker output.
Reviews
There are no reviews yet.