DSM501A (Dust Sensor Module)
DSM501A Dust Sensor Module PM2.5 Detection Dector Allergic Smoke Particles Sensor Module which can be used with Arduino for Air Conditioning, Air Cleaning, Air Quality Monitoring and ventilator systems.
Description
Overview:
The dust sensor module DSM501A (Datasheet) is low cost,compact size for a particle density sensor.
- Quantitative particle measurement with the principle of particle counter.
- FIne particle of which diameters are bigger than one micron could be detected with high sensitivity.
- Inside heater realizes the self-air taking.
- One control contact and two output contacts.
The DSM501A consists of:
- Light Emitting Diode(LED) Lamp
- Detector
- Signal amplifier circuit
- Output drive circuit 1
- Output drive circuit 2
- Heater
Features:
- PWM output
- Compact size and lightweight
- Easy installation
- Single power supply
Application:
- Air cleaner or Air purifier
- Air condition
- Air quality monitor
- Ventilator etc.
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
GO2Y0A21YK
GO2Y0A21YK
Infrared distance measuring sensor (including dedicated data line)Technical Parameters:
- Model : GP2Y0A21YK (GP2D12 upgrade)
- Voltage: 4.5-5. 5V
- Current: 33-40mA
- Port: Analog
- Detection distance: 10-80cm
- Data line: 3P 20cm
- Wire: 24# American standard line
- Interface: 3P DuPont SVG compatible Arduino sensor expansion board
KY-028 -Temperature sensor module (Digital)
Product Features:
- Using the NTC thermistor sensor , good sensitivity.
- The comparator output signal is clean, good waveform , driving ability , more than 15mA.
- Adjust the temperature distribution position detection threshold.
- The working voltage: DC 3.3V-5V.
- The output format : digital switching outputs ( 0 and 1 )
- A fixed bolt holes for easy installation.
- Using a wide voltage LM393 comparator.
MAX6675-(Temperature Sensor With Thermocouple Cable)
MAX6675 Module + K Type Thermocouple Sensor:
The MAX6675 performs cold-junction compensation and digitizes the signal from a type-K thermocouple. The data is output in a 12-bit resolution, SPI™-compatible, read-only format. This converter resolves temperatures to 0.25°C, allows readings as high as +1024°C, and exhibits thermocouple accuracy of 8LSBs for temperatures ranging from 0°C to +700°C.
MQ-6 LPG Gas Sensor Module
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 300 to 10000ppm. This sensor has a high sensitivity and fast response time. The sensor’s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
TMP006 (Contact-less Infrared Temperature Measurement)
The TMP006 works with 3v to 5v, so it can be used with most microcontrollers without the need for a level shifter. It connects via the i2c bus and is addressable so you can have up to 8 TMP006 sensors on the same bus.
Features:
- 20mm x 20mm (board w/o headers)
- Uses I2C 7-bit addresses between 0x40 and 0x47, selectable with jumpers
- Interface Type : I2C Arduino driver module
Reviews
There are no reviews yet.