USB to TTL FT232RL (3.3V/5V) FTDI Serial Converter Module for Arduino
Original price was: ₨700.00.₨650.00Current price is: ₨650.00.
Product Specification:
- The FT232R is a USB to serial UART interface
- A low-cost way to add USB capability to microcontrollers. Use this to give your own breadboard For USB capability for bootloading or downloading sketches.
- RXD/TXD transceiver communication indicator
- Includes over-current protection, using a 500ma self-restoring fuse
- This board includes a DTR pin needed to auto-reset when downloading to your device.
- Color: Red
- USB Power Supply: 3.3V or 5V (Selectable)
- Header pitch: 2.54mm
- Size:43*17mm
Product Description:
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
This board has TX and RX LEDs that make it a bit better to use over the FTDI cable. You can actually see serial traffic on the LEDs to verify if the board is working. This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro boards and LilyPads use this type of connector. One of the nice features of this board is a Switch on the back of the board that allows the board to be configured to either 3.3V or 5V (both power output and IO level).
Product Features:
The FT232RL is a USB to serial UART interface IC with the following advanced features:
-
- Single-chip USB to asynchronous serial data transfer interface.
- Entire USB protocol handled on the chip. No USB specific firmware programming required.
- Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
- Fully integrated USB termination resistors.
- Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
- Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
- 128 byte receive buffer and 256 bytes transmit buffer utilizing buffer smoothing technology to allow for high data throughput.
Features of FT232RL USB TO TTL 5V 3.3V Convertor:
-
- Material: PCB + Electronic Component
- USB power has over current protection, using 500MA self-restore fuse
- RXD/TXD transceiver communication indicator
You must be logged in to post a review.
Related products
Leonardo R3 Development Board ATMEGA32U4
Product specifications:
• Controller: ATmega32u4 • Work record: 16 MHz • Working voltage: 5V • Input voltage (recommended): 7-12V • Digital IO port: 20 • PWM channel: 7 • Analog input: 12 • 5V digital / analog port maximum allowable current: 40 mA • 3.3V digital / analog port maximum allowable current: 50 mA • Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader • SRAM: 2.5 KB (ATmega32u4) • EEPROM: 1 KB (ATmega32u4)
Raspberry Pi 3 Model B (1GB)
U-BLOX NEO-6M module (GY-GPS6MV2)
- 1 — u-blox NEO-6M GY-GPS6MV2 GPS module with on board EEPROM
- 1 — GPS antenna
- 1 — 1x4 male header
uLCD-32PTU-Pi (3.2″ Raspberry Pi Display Module for the Raspberry Pi A, B and B+)
| Manufacturer | 4D Systems |
| Type of display | TFT |
| Screen size | 3.2" |
| Display resolution | 240x320 |
| Supply voltage | 5V DC |
| Contrast | 450:1 |
| Luminosity | 250cd/m2 |
| No. of colours | 65k |
| Window dimensions (H x W) | 48.6 x 64.8mm |
| Dimensions | 56.32 x 92.19 x 15.9mm |
| Kind of display | graphical |
| Microcontroller | PICASO |
| Series | Raspberry Pi |
| Viewing angle | 150° |
XBee 1mW Wire Antenna
Description:
- 3.3V @ 50mA
- 250kbps Max data rate
- 1mW output (+0dBm)
- 300ft (100m) range
- Wire antenna
- Fully FCC certified
- 6 10-bit ADC input pins
- 8 digital IO pins
- 128-bit encryption
- Local or over-air configuration
- AT or API command set
Reviews
There are no reviews yet.