SHT31 (Digital Temperature and Humidity Sensor Module)
General Features:
- Highly reliable, accurate and quick response time
- I2C interface
- Well calibrated, linearized, compensated for digital output
- Highly abstracted development library
Specification:
- Input voltage (VCC): 3.3 volts or 5 volts
- I/O Logic Level : 3.3 volts or 5 volts based on VCC
- Operating Current : 100 μA
- Operating Temperature : -40–125 ℃
- Temperature Sensor Range : -40–125 ℃, with ±0.3°C accuracy
- Humidity Sensor Range : 0% – 100%(Relative Humidity), with ±2% accuracy
- Sensor Chip : SHT31
- I2C
Description
Description:
The SHT31 sensor could be the finest and highest-accuracy humidity sensor you can find, as it can acquire the relative humidity at only ±2% error. On the other side it also features an excellent performance in terms of temperature measurement, you can use it in some extreme conditions, like -40 degree or 125 degree, and it still keeps an accuracy of ±0.3 degree.
Unlike earlier SHT sensors, this sensor has a true I2C interface, and even with two address options. It is also 3V or 5V compliant, so you can power and communicate with it using any microcontroller or microcomputer.
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
CJMCU-175 (Digital Temperature Sensor Module)
General Features:
CJMCU-175 Digital Temperature Sensor TMP175 27 Address
Digital output: SMBusTM, two-wire and I2C interface compatibility
Resolution: 9 to 12 digits, user selectable
Wide supply voltage range: 2.7V to 5.5V
TMP175 allowing up to 27 devices on a bus member.
It is a negative temperature desired coefficient thermistor (NTC) and positive temperature coefficient (PTC) for generation
The device provides a typical ±1°C accuracy without calibration or external component signal conditioning .
The on-chip 12-bit analog -to- digital converter (ADC) provides resolution down to 0.0625°C.
KY-028 -Temperature sensor module (Digital)
Product Features:
- Using the NTC thermistor sensor , good sensitivity.
- The comparator output signal is clean, good waveform , driving ability , more than 15mA.
- Adjust the temperature distribution position detection threshold.
- The working voltage: DC 3.3V-5V.
- The output format : digital switching outputs ( 0 and 1 )
- A fixed bolt holes for easy installation.
- Using a wide voltage LM393 comparator.
MAX6675-(Temperature Sensor With Thermocouple Cable)
MAX6675 Module + K Type Thermocouple Sensor:
The MAX6675 performs cold-junction compensation and digitizes the signal from a type-K thermocouple. The data is output in a 12-bit resolution, SPI™-compatible, read-only format. This converter resolves temperatures to 0.25°C, allows readings as high as +1024°C, and exhibits thermocouple accuracy of 8LSBs for temperatures ranging from 0°C to +700°C.
MQ-7 (Carbon Monoxide Gas Sensor Module)
MQ-7 Carbon Monoxide Gas Sensor Module is used to detect Carbon Monoxide (CO) concentration, it can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The module outputs a voltage from 0 to 5V relative to the CO concentration. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.
T000220 (Arduino TinkerKit Touch Sensor Module)
This TinkerKit sensor is a touch sensitive device that provides an output when it detects skin contact. The sensor is connected to an Arduino board via a TinkerKit Shield to form part of the TinkerKit modular prototyping system.
- Based on a QT 100A single touch controller
- On-board-signal amplifier
- Green LED for correct power indication
- Yellow LED whose brightness depends on the values output by the module
TTP229-LSF (Capacitive Touch Keypad Module)
Features:
- On board 8 capacitive touch keys and 1 linear capacitive sensor
- Features TONTEK TonTouch touch pad detector IC TTP229-LSF, supports up to 16 keys with adjustable sensitivity and built-in LDO
- The system recalibrates automatically when all keys are not detected touch more than about 4 seconds
- Customizable functions:
- 8 keys or 16 keys option
- 8 individual outputs or batch production
- Single-key or multi-kye feature
- Sampling rate and duration of sampling in sleep mode
- The maximum key is on time
Reviews
There are no reviews yet.