SCT-013-000 (YHDC Non-Invasive Current Transformer) 30A,100A
Overview:
- Home Automation and Control applications where Current measurement is needed.
- Suitable for the current measuring
- Monitoring and protection of AC motor
- Lighting equipment
- Air compressor
- Frequency: 50Hz-150KHz
- Rated input current: 30A 100A (2xOptions)
- Mouth open size: 13mm*13mm
- Operating temperature: -25-70’C
Description
Description
This is non-invasive CT (Current Transformer) sensor, based on the magnetive transomfer working principle, which is hard to be explained by us but you can read a lot on this current transformer wiki page, or similar device “current clamp”. If you are interesting on power energy measurement, power grid, or measuring any alive domestic appliance or your system, this is one thing fun to try.
Applications
- Suitable for the current measuring
- Monitoring and protection of AC motor
- Lighting equipment
- Air compressor
Specifications
- Non-linearity: ±3%
- Turn Ratio: 100A:0.05A
- Resistance Grade: Grade B
- Work Temperature: -25°C ~ ﹢70°C
- Dielectric Strength(between shell and output): 1000V AC/1min 5mA
- Leading Wire in Length: 1m
- Open Size: 13mm x 13mm
For 100A AC Version: sensing current: 0~100A AC; Output Mode: 0~50mA
For 30A AC Version: sensing current: 0~30A AC; Output Mode: 0~1V
Downloads:
Reviews (0)
You must be logged in to post a review.
Shipping & Delivery
Related products
CJ1WTS562 (Temperature Sensor Module Screw Terminal Connection)
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers
Highlights/Features:
Omron Temperature sensor module is suitable for use with cj1 series programmer controllers These temperature sensor units are classified as digital I/O units when considering I/O allocations and will take digital I/O points from the total allocation for a CJ1M CPU. The number of I/O points is DIP switch selectable as follows; configured for 1 - 3 inputs takes 48 digital I/O points, configured for 4 inputs takes 64 digital I/O points and configured for 5 - 6 inputs takes 96 digital I/O points.
Current Transformer- ZMCT118F 30A
(Ask For A Quotation)
A current transformer (CT) is used for measurement of alternating electric currents. When current in a circuit is too high to apply directly to measuring instruments, a current transformer produces a reduced current accurately proportional to the current in the circuit, which can be conveniently connected to measuring and recording instruments. A current transformer isolates the measuring instruments from what may be very high voltage in the monitored circuit.
Features
- Small size
- High accuracy, and good consistency,for current and power measurement
- ZMCT118F can measure the AC current upto 30 amps
- Output proportional to AC current
GO2Y0A21YK
GO2Y0A21YK
Infrared distance measuring sensor (including dedicated data line)Technical Parameters:
- Model : GP2Y0A21YK (GP2D12 upgrade)
- Voltage: 4.5-5. 5V
- Current: 33-40mA
- Port: Analog
- Detection distance: 10-80cm
- Data line: 3P 20cm
- Wire: 24# American standard line
- Interface: 3P DuPont SVG compatible Arduino sensor expansion board
Motion Detecting Module- Zilog ePIR
Zilog's ePIR is a fully functional motion-detecting single-board computer (SBC). Combined on this board are a Z8 Encore! XP MCU, and a Murata passive infrared (PIR) sensor, which is shielded by a Fresnel lens. Taking advantage of the processing capabilities of the Z8 MCU, the ePIR uses a powerful new statistical processing method to provide exceptional motion detection performance.
MQ-7 (Carbon Monoxide Gas Sensor Module)
MQ-7 Carbon Monoxide Gas Sensor Module is used to detect Carbon Monoxide (CO) concentration, it can detect CO-gas concentrations anywhere from 20 to 2000ppm. This sensor has a high sensitivity and fast response time. The module outputs a voltage from 0 to 5V relative to the CO concentration. The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.
Reviews
There are no reviews yet.