RASPBERRY Pi Zero Camera Cable
The Raspberry Pi Zero and Zero W are both equipped with a smaller CSI (Camera Serial Interface) port than on a full-sized Raspberry Pi board — luckily, that’s where this cable can help! The Raspberry Pi Zero Camera Cable replaces the pre-existing camera module cable, allowing your Zero or Zero W light and imaging capabilities.
This cable measures 15cm from end to end and can easily be swapped in and out.
Note: This product only includes the CSI cable and does NOT include a Raspberry Pi Camera Module. The module will need to be purchased separately.
You must be logged in to post a review.
Related products
High-Speed Mini-HDMI to HDMI Cable – 10 Feet
Industrial Grade UTEK UT-8801 USB to RS-232 Converter Ver 2.0(1-port USB to RS-232 Serial Converter with ESD protection)
Product Introduction:
-
Allows to connect RS232 device to your computer by USB port.
-
FTDI FT232 + 213 chip
-
All 9-wires out
- Real USB 2.0 specification is compliant for faster and steadier data communication.
-
USB bus-powered and no need external power required.
-
Supports Windows 98SE, ME, 2000, XP, Vista, Windows 7, Win 10, Linux v5.0 or above & Mac OS 8.6 or above.
-
cable length 1.5m
Passive RS232 to RS485 communication protocol converter (STM485S)
Overview:
In order to communicate between computers, external devices, and intelligent instruments with different serial port standards, we must first convert the communication signals.This converter is compatible with RS-232C and RS-485 standards. It can convert single-ended PS-232 signals into balanced RS-485 differential signals, and extend the communication distance to 1.2 kilometers. The converter is passive and does not require external power. It uses a special current pump technology to take power from RS-232 signals (RTS, DTR, TXD) without the need to initialize the RS-232 interface in advance.
UTEK UT-2211 (Port-powered Mini RS-232 to RS-485) 600w Surging Protection
Product Review:
● Standards: RS-232C,RS-485 EIA/TIA ● Connector: RS-232 DB9 female, RS-485 terminal block ● Operating mode: asynchronous half-duplex, differential transmission ● Transmission media: twisted-pair or shielded wire ● Baud rate: 300BPS-115.2KBPS ● Dimension: 58mm×33mm×19.5mm ● Working temperature: -25℃ to 70℃ ● Relative humidity: 5% to 95% ● Transmission distance: 1,200m(RS-485), 5m(RS-232)
UTEK UT-732i- Commercial Grade PCI to 2-Port RS485 High-Speed Serial Card Opto-Isolated Computer Serial Expansion Card (with 2 Serial Cable 9-pin Com Ports)
Introduction:
- Connector: DR44 female x1
- BUS: 32 bits universal PCI
- Signal: RS-422：T/R+, T/R-, RXD+, RXD-, GND
RS-485：Data+(A) Data-(B) GND
- Transmission rate: 300bps-921.6Kbps
- Data bits: 5, 6, 7, 8
- Stop bits: 1, 1.5, 2
- Check bits: None, Even, Odd, Space, Mark
- Flow control: RTS/CTS XON/XOFF
- Operating temperature: -40℃～85℃
- Optical isolation: 2,500Vrms isolated voltage, 500DC continuous specialized DC/DC module
- Interface protection: RS-422 & RS-485 provides with 2KV lightning surge, ±15KV ESD protection
- Transmission distance: 1.2km for RS-485/422
- System: Win98/2000、WinXP/2003/Vista/2008/7/8/8.132/64, DOS/Linux 2.4/2.6
UTEK- UT-712 (2-ports RS485/422 PCI/PCI-Express to Serial)
Specification:
- Hardware Interface:
- Connector: DB9 male 2
- Bus: 32 bit Universal PCI
- Signal: RS-422: T/R+, T/R-, RXD+, RXD-, GND RS-485: Data+ (A) Data- (B) GND
- Transmission: 300bps-115.2kbps
- Data bits: 5, 6, 7, 8
- Stop bits: 1, 1.5, 2
- Parity: None, Even, odd, Space, Mark
- Flow Control: RTS/CTS XON/XOFF
- Operating Temperature: 0~70℃
- Optical Isolation Protection: Isolation Voltage2500Vrms 500VDC Continuous DC/DC Module
- Interface Protection: 600W Surge Protection each line for RS-422andRS-485 interface ESD Protection
- Transmission: 1-1200meters (115200bps-9600bps)
- Operating Systems: Windows 2003/XP/2000/98/ME, Linux, UNIX Drivers
Reviews
There are no reviews yet.