Micro SD TF Memory Card Shield Module SPI For Arduino
Features:
Supports Micro SD cards, Micro SDHC card(Micro SD<=2G, Mirco SDHC<=32G).
Level conversion circuit board that interfaces level for 5V or 3.3V.
Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board.
It is a standard SPI communication interface.
4 M2 screw positioning holes for easy installation.
Description:
The module(Micro SD Card Adapter) is a Micro SD card reader module, through the file system and the SPI interface driver, MCU to complete the file system to read and write MicroSD card. Users can directly use IDE comes with an SD card to complete the library card initialization and read-write.
Features
– Support Micro SD Card, Micro SDHC card (high-speed card)
– The level conversion circuit board that can interface level is 5V or 3.3V
– Communication interface is a standard SPI interface
– Control Interface: a total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground
– VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin
– 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply
– Level conversion circuit: micro SD card into the direction of signals into 3.3V,
– MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal
– Micro SD card connector: yes since the bomb deck for easy card insertion and removal
– Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, easy to install positioning, to achieve inter-module combination
Specifications
– Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board
– Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm
– Control Interface: GND, VCC, MISO, MOSI, SCK, CS
– Size: 42x24x12mm
Package Includes
1 x Micro SD Storage Board Micro SD TF Card Memory Shield Module SPI for Arduino
You must be logged in to post a review.
Related products
Arduino WiFi Shield with Integrated Antenna A000058
Overview:
The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits.- Requires and Arduino board (not included)
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Persoanl
- Connection with Arduino on SPI port
- on-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Mini-USB for updating WiFi shield firmware
GLT240128-WB (LCD Graphic RS 232 BLU/WHT)
Leonardo R3 Development Board ATMEGA32U4
Product specifications:
• Controller: ATmega32u4 • Work record: 16 MHz • Working voltage: 5V • Input voltage (recommended): 7-12V • Digital IO port: 20 • PWM channel: 7 • Analog input: 12 • 5V digital / analog port maximum allowable current: 40 mA • 3.3V digital / analog port maximum allowable current: 50 mA • Flash Memory: 32 KB (ATmega32u4) of which 4 KB used by bootloader • SRAM: 2.5 KB (ATmega32u4) • EEPROM: 1 KB (ATmega32u4)
MICO Shield for Arduino
U-BLOX NEO-6M module (GY-GPS6MV2)
- 1 — u-blox NEO-6M GY-GPS6MV2 GPS module with on board EEPROM
- 1 — GPS antenna
- 1 — 1x4 male header
UNO R3 Sensor Shield V5 Expansion Board For Arduino
- Ready to plug & play.
- It can connect to various modules like sensors, servos, relays, buttons, potentiometers
- Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already. Buckled brick cables are like cement for bricks, make the connections easier, secure and more professional looking.
Reviews
There are no reviews yet.